Criteria

Text:
Content:
Display:

Results

Viewing 9601 to 9630 of 10229
2008-07-09
Article
The Cadillac Provoq concept, announced at this year's Consumer Electronics Show in Las Vegas and shown in Detroit, is another example of General Motors’ E-Flex propulsion system, this time combining a new fifth-generation fuel-cell system and a lithium-ion battery pack.
2008-07-09
Article
Ringfeder offers seven additional Arcusaflex flywheel coupling sizes by Reich Kupplungen for larger engine applications, bringing the total available to 21 sizes, with torque ranges from 147.5 to 81,132 lb·ft (200 to 110,000 N·m).
2008-07-09
Article
To achieve compliance with Interim Tier 4/Stage IIIB mobile off-highway emissions regulations for engines 130 kW (174 hp) and above, John Deere Power Systems plans to use its Tier 3 PowerTech Plus engine platform, add a diesel oxidation catalyst/diesel particulate filter (DOC/DPF) unit for reducing particulates, and increase the percentage of cooled exhaust gas recirculation for NOx control.
2008-07-09
Article
To maintain clean, contaminant-free oil, UFI Filters offers the Trans Care TA-TB oil filtration series.
2008-07-09
Article
FEV offers a unit that allows the autonomous control of various emissions control systems, such as NOx adsorber catalyst-diesel particulate filter (DPF) or selective catalytic reduction-DPF systems.
2008-07-09
Article
The Racor Division of Parker Hannifin releases the EAF68133 heavy-duty air cleaner for off-highway applications.
2008-07-09
Article
The C1.6 from Caterpillar offers 24.6 and 26.5 kW (33 and 35.5 hp) at 2800 and 3000 rpm, respectively. Designed to meet 2008 Tier 4A, Stage IIIA emissions requirements, the C1.6 offers a top speed of 3000 rpm.
2008-07-09
Article
Plasma3 VCP from Enercon provides variable chemistry atmospheric plasma for difficult-to-treat surfaces.
2008-07-09
Article
Safety advocates are trying to determine what potential technologies are the most substantive and what technologies do not meet the hype. A panel session at April's SAE World Congress, Strategies for Active Safety Technology Delivery, touched on NHTSA’s Advanced Collision Avoidance Technologies (ACAT) program.
2008-07-09
Article
Since its introduction in 1996, OnStar has grown to five million subscribers, has gone across the board on General Motors vehicles, and is expanding its menu of services.
2008-07-09
Article
In the nearly four decades since the U.S. arrival of the Datsun 240Z, many new sport coupes have claimed to be that car’s modern equivalent, but Hyundai’s Genesis Coupe may finally be the true second coming.
2008-07-09
Article
Midway through the development program for the 2009 Nissan Maxima, the company realized it was headed down a dead-end road. Designers and engineers refocused the program with the aim of returning the Maxima to its “four-door sports car” roots, emphasizing responsive handling, braking, and acceleration.
2008-07-09
Article
As expected, Rolls-Royce has announced that it is also taking the (relatively) more compact design route with an all-new model. The car, code-named RR4, will be built at its Goodwood plant in the UK and will be launched in 2010.
2008-07-09
Article
The HMC 1250 from MAG Giddings & Lewis is a 1250 mm (49 in) horizontal machining center that brings shorter cycle times to heavy cutting while providing modular design to meet application needs.
2008-07-09
Article
Air traffic controllers around the country are using the advanced air traffic control planning technology developed by the Lockheed Martin URET development team to safely route aircraft more efficiently.
2008-07-09
Article
The power on of Boeing's 787 was accomplished using TTTech's design tools, embedded commercial-off-the-shelf software, and platform integration services based on time-triggered protocol.
2008-07-09
Article
At April’s SAE 2008 World Congress held in Detroit, Henkel Corp. showed and explained an array of products and technologies from the minds of its engineers. Foremost among them was its Aquence autodeposition coating technology, which, according to the company, sets an industry precedent by displacing conventional metal pretreatment and the electrocoat process for an entire automotive vehicle body.
2008-07-09
Article
Applied Process’ Carbo-Austempering process is a high-performance steel heat treatment that excels when high fatigue strength and wear resistance are required.
2008-07-09
Article
The Keyence high-speed LJ-G Series 2-D laser sensors accurately measure the surface profile of targets in the x and z directions.
2008-07-09
Article
Expansion of Misumi USA's single-axis actuator lines with new models and sizes brings its total configurations to more than 2600.
2008-07-09
Article
Two electrically heated, 500°F (260°C) universal ovens from Grieve are modified for simultaneous operation with reduced movement by one worker at the customer’s facility in the performance of general heat-processing operations.
2008-07-09
Article
Micronor’s TD5207 nonmetallic fiber-optic rotary encoder operates in extreme electromagnetic environments.
2008-07-09
Article
ACTech GmbH has produced customized small batches and individual castings for the mining industry using rapid prototyping technology developed from the automotive and aerospace industries.
2008-07-09
Article
The Tricept T9000 parallel kinematic machine system from Hartwig can perform milling, drilling, routing, deburring, and finishing; optical inspection and touch probing; fastener/rivet installation; and friction stir welding with just a change of tooling.
2008-07-09
Article
The Temperature Product Group of Measurement Specialties not only offers a large selection of standard thermistor components and probes, but also provides custom solutions expertise.
2008-07-08
Article
The Push-Lok Plus hose product line from Parker features a wide fluid-compatibility range and a diverse application and size range.
2008-07-08
Article
Hydac Hydraulics offers custom manifolds designed to simplify system procurement and reduce acquisition costs through single subassembly sourcing.
2008-07-08
Article
To address evolving industry challenges and requirements, Simrit offers updated global material and design solutions, including NOK U641, G928 HNBR, and NOK UH05 urethanes, as well as a sealing design that offers high-pressure system ability.
2008-07-08
Article
Hawe Hydraulics’ PSL proportional directional spool valve controls the direction of motion while delivering speed control regardless of load type and weight.
2008-07-08
Article
Nissan Motor Manufacturing in Europe is replacing some metal underhood components with high-performance polymers. It is using DuPont’s Minlon and Zytel products for the rocker cover and front cover of its 2.5-L turbodiesel engine.
Viewing 9601 to 9630 of 10229